| MRC | Criteria | Characteristic |
|---|
| CSDH | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT FULL RATED POWER | 25.0 SINGLE SECTION |
| FEAT | SPECIAL FEATURES | KNOB ON REAR END OF SHAFT 0.6232 IN. DIA MIN. AND 0.6238 IN. DIA MAX; 500 OHM,0.25 WATT INTERNAL RESISTOR CONNECTED TO WIPER |
| TEST | TEST DATA DOCUMENT | 82577-960024 DRAWING THIS IS THE BASIC GOVERNING DRAWING,SUCH AS A CONTRACTOR DRAWING,ORIGINAL EQUIPMENT MANUFACTURER DRAWING,ETC.; EXCLUDES ANY SPECIFICATION,STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWI |
| TTQY | TERMINAL TYPE AND QUANTITY | 4 TURRET |
| AAPN | SECTION QUANTITY | 1 |
| AAQL | BODY STYLE | CYLINDRICAL SERVO MOUNTED |
| AARG | RELIABILITY INDICATOR | NOT ESTABLISHED |
| AAVL | PILOT DIAMETER | 1.8745 INCHES MINIMUM AND 1.8750 INCHES MAXIMUM |
| AAVM | PILOT LENGTH | 0.0350 INCHES MINIMUM AND 0.0670 INCHES MAXIMUM |
| ABPA | UNDERCUT DIAMETER | 1.8745 INCHES MINIMUM AND 1.8750 INCHES MAXIMUM |
| ABPC | UNDERCUT WIDTH | 0.0550 INCHES MINIMUM |
| ABPM | BODY DIAMETER | 2.000 NOMINAL CENTIMETERS |
| ABUF | ANGLE OF MOUNTING HOLE IN DEG | 30.0 |
| ABVJ | ANGLE BETWEEN CENTERLINES OF MOUNTING HOLES IN DEG | 60.0 |
| ABWV | SHAFT DIAMETER | 0.2495 INCHES MINIMUM AND 0.2500 INCHES MAXIMUM |
| ABXF | SHAFT LENGTH | 2.155 INCHES MINIMUM AND 2.208 INCHES MAXIMUM |
| ADAQ | BODY LENGTH | 0.910 INCHES MAXIMUM |
| AECZ | MOUNTING LIP DIAMETER | 2.0000 INCHES MAXIMUM |
| AEDA | MOUNTING LIP DEPTH | 0.0550 NOMINAL MILS AND 0.0670 NOMINAL CENTIMETERS |
| AEDE | MOUNTING HOLE/STUD CIRCLE DIAMETER | 1.682 INCHES MINIMUM AND 1.692 INCHES MAXIMUM |
| AEDX | SHAFT STYLE | ROUND,SLOTTED |
| AEDZ | SHAFT BEARING TYPE | BALL |
| AEFD | ACTUATOR TYPE | DOUBLE ENDED SHAFT |
| AEFH | EFFECTIVE ELECTRICAL ROTATION IN DEG ANGULAR ROTATION | 350.0 NOMINAL |
| AEFK | MAXIMUM STARTING TORQUE | 0.60 INCH-OUNCES |
| AEFL | MAXIMUM RUNNING TORQUE | 0.60 INCH-OUNCES |
| AEFY | SHAFT END PLAY | 0.005 INCHES |
| AEFZ | SHAFT RUNOUT | 0.002 INCHES |
| AEGA | LATERAL RUNOUT | 0.002 INCHES |
| AEGB | PILOT DIAMETER RUNOUT | 0.001 INCHES |
| AEGC | SHAFT RADIAL PLAY | 0.001 INCHES |
| AFJN | FRAGILITY FACTOR | MODERATELY RUGGED |
| AJYN | SCREW THREAD DIAMETER | 0.076 INCHES MINIMUM AND 0.096 INCHES MAXIMUM |
| AJYP | SCREW THREAD SERIES DESIGNATOR | UNC |
| AJYQ | SCREW THREAD QUANTITY PER INCH | 56.0 |
| AKPV | MOUNTING FACILITY QUANTITY | 4 |
| APXH | TERMINAL LOCATION | RADIALLY POSITIONED OVER MORE THAN HALF THE CIRCUMFERENCE |
| AXGY | MOUNTING METHOD | CLAMP RING AND THREADED HOLE |
| CBBL | FEATURES PROVIDED | HUMIDITY PROOF |
| CBME | CUBIC MEASURE | 0.910 CUBIC INCHES |
| CQCC | ELECTRICAL RESISTANCE PER SECTION | 2.0 PERCENT,RATED AMPERES C AND BETTER FLOORING |
| CQCH | TAP LOCATION FROM CCW TERMINAL PER SECTION IN DEG OF EFFECTIVE ELECTRICAL ROTATION | 1000.0 SINGLE SECTION |
| CQCK | ROTARY ACTUATOR TRAVEL IN ANGULAR DEG | 360.0 NOMINAL |
| CQFL | FUNCTION CONFORMITY TOLERANCE PER SECTION | 0.10/0.10 SINGLE SECTION |
| CQGN | AMBIENT TEMP IN DEG CELSIUS PER SECTION AT ZERO PERCENT RATED POWER | 125.0 SINGLE SECTION |
| CRFJ | TEMP COEFFICIENT OF RESISTANCE PER SECTION IN PPM PER DEG CELSIUS | 400.0/400.0 SINGLE SECTION |
| CRGD | POWER DISSIPATION RATING PER SECTION IN WATTS | 2.0 7TH SECONDARY QUALITY |
| CRGM | FUNCTION CONFORMITY PER SECTION | SINGLE SECTION INDEPENDENT LINEARITY |
| CRJS | FIXED TAP QUANTITY PER SECTION | 1 SINGLE SECTION |
| CRSS | RESISTANCE TOLERANCE PER SECTION IN PERCENT | 10.0/10.0 SINGLE SECTION |
| CRSX | ACTUATOR TRAVEL CONTROL FEATURE | CONTINUOUS MOTION |
| CSBX | FUNCTION CHARACTERISTIC PER SECTION | 7 OCLOCK ALL PRIMARIES |
